Drop jump · Reactive strength
Drop jump and Reactive Strength Index (RSI)
The Reactive Strength Index (RSI) is jump height divided by ground contact time in a drop jump. It shows how much height you get out of how little time on the ground – the higher, the more reactive.
The formula
RSI = jump height (m) ÷ ground contact time (s) → unit m/s
Example: flight time 500 ms → jump height 30.6 cm (h = g · T² / 8); ground contact 200 ms → RSI 1.53 m/s, ± 0.11 m/s at 240 fps.
What is a drop jump?
In a drop jump you step off a box, and right after touchdown you jump up again as high as you can. Two times are measured: how long you are on the ground (ground contact time) and how long you fly afterwards (flight time, which gives the height).
According to Flanagan and Comyns (2008), ground contact time and RSI help to steer plyometric training, track progress and motivate athletes. In a study with 22 people and a 30 cm drop, jump height, contact time and RSI were highly reproducible from trial to trial (ICC above 0.9; Flanagan, Ebben and Jensen 2008).
Typical values
We have not found generally valid RSI norms in any reliable source (as of 29 Oct 2026), so we don’t list any. The RSI changes with drop height and jumping technique. What makes sense is comparing yourself with yourself – always from the same box.
How Powerleap measures the drop jump
Setup
iPhone at the side as for a normal jump, the whole box in the picture. Stand on the box and wait for the beep.
Detection
The app sees from the raised stance that this is a drop jump and treats the ground contact after the drop as the floor.
Three marks
Touchdown after the drop (first frame with ground contact), take-off (first frame with both feet in the air) and landing (first frame with ground contact).
Calculation
Contact time = take-off − touchdown. Height from flight time (h = g · T² / 8). RSI = height ÷ contact time. Plus the effective drop height from the speed at touchdown (v² / 2g).
| Quantity | Accuracy at 240 fps |
|---|---|
| Each mark | ±1 frame = ±4.2 ms |
| Contact time, flight time | ±2 frames each = ±8.3 ms (frame grid; contact time not yet reliable for landings on the balls of the feet, see below) |
| RSI | ± RSI · (2 · δflight / flight time + δcontact / contact time); the app shows it for every measurement |
| Plausibility | the app rejects contact times below 60 ms or above 1.2 s as implausible |
The ± values in the table come from the frame grid of ±1 frame per mark; they have not yet been checked on real drop jumps. With a landing on the balls of the feet, touchdown came 3–4 frames too early in the simulation (camera at 0.75 m) and contact time 1–3 frames (4–13 ms) too long. Real drop jumps with hand-set marks are still pending, so check touchdown and take-off in the video.
For the drop jump the app calculates the height from plain flight time; if you touch down with clearly bent knees (center of mass lower than at take-off), it shows a hint. So land with straight legs. Drop jumps have their own history with the RSI as the main number.
Repeated jumps: RSI for every jump
In repeated jumps you jump 5–10 times in quick succession. Powerleap shows ground contact and RSI for every jump and the mean RSI of the series, calculated here as flight time ÷ contact time. Repeated jumps have their own history and no records. As in the drop jump, contact time is not yet reliable with a landing on the balls of the feet.
Build up drop jumps gradually and only train when you’re healthy. Powerleap is a training tool, not a medical device.
Frequently asked questions
What is a good RSI?
We have not found generally valid norms in any reliable source (as of 29 Oct 2026). The RSI changes with drop height and jumping technique. So compare your values with yourself, always from the same box.
How do you calculate the RSI?
Jump height in meters divided by ground contact time in seconds. Example: 0.30 m jump height and 0.200 s ground contact give an RSI of 1.5 m/s.
How accurately does Powerleap measure contact time?
The frame grid gives ±1 frame per transition. Contact time depends on two transitions (touchdown and take-off), so at 240 frames per second that is ±8.3 ms; the app shows this ± for every RSI. With a landing on the balls of the feet, touchdown came 3–4 frames too early in the simulation (camera at 0.75 m) and contact time 1–3 frames (4–13 ms) too long. Real drop jumps with hand-set marks are still pending, so check touchdown and take-off in the video.
What is the difference between RSI and RSImod?
The RSI belongs to the drop jump: height ÷ ground contact time. The modified RSI (RSImod) belongs to the jump from standing: height ÷ time from the start of the dip to take-off. Powerleap shows it as “explosiveness”.
Sources
- Flanagan EP, Comyns TM (2008). The Use of Contact Time and the Reactive Strength Index to Optimize Fast Stretch-Shortening Cycle Training. Strength Cond J 30(5):32–38. doi.org/10.1519/SSC.0b013e318187e25b
- Flanagan EP, Ebben WP, Jensen RL (2008). Reliability of the reactive strength index and time to stabilization during depth jumps. J Strength Cond Res 22(5):1677–1682. doi.org/10.1519/JSC.0b013e318182034b